AudioCodes MediaPack 114 Manual do Utilizador Página 362
- Página / 390
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
SIP User's Manual 362 Document #: LTRT-65411
MediaPack Series
To configure MWI, set the following parameters:
EnableMWI (or using the Web interface, refer to ''Supplementary Services'' on page
138)
MWIServe
rIP (or using the Web interface, refer to ''Supplementary Services'' on page
138)
MWIAnalo
gLamp (or using the Web interface, refer to ''Supplementary Services'' on
page 138)
MWIDi
splay (or using the Web interface, refer to ''Supplementary Services'' on page
138)
StutterTone
Duration (or using the Web interface, refer to ''Supplementary Services'' on
page 138)
EnableM
WISubscription (or using the Web interface, refer to ''Supplementary
Services'' on page 138)
MWIExpiratio
nTime (or using the Web interface, refer to ''Supplementary Services'' on
page 138)
Subscri
beRetryTime (or using the Web interface, refer to ''Supplementary Services'' on
page 138)
Subscri
ptionMode (or using the Web interface, refer to ''Proxy & Registration
Parameters'' on page 112)
Calle
rIDType -- determines the standard for detection of MWI signals (or using the
Web interface, refer to ''Supplementary Services'' on page 138)
ETSIVMWITypeOn
eStandard (for a description, refer to ''Analog Telephony
Parameters'' on page 279)
Bellco
reVMWITypeOneStandard (for a description, refer to ''Analog Telephony
Parameters'' on page 279)
7.14.7 Caller ID
This section discusses the device's Caller ID support.
7.14.7.1 Caller ID Detection / Generation on the Tel Side
By default, generation and detection of Caller ID to the Tel side is disabled. To enable
Caller ID, set the parameter EnableCallerID to 1. When the Caller ID service is enabled:
For FXS: the Caller ID signal is sent to the device's port
For FXO: the Caller ID signal is detected
The configuration for Caller ID is described below:
Use the parameter CallerIDType to define the Caller ID standard. Note that the Caller
ID standard that is used on the PBX or phone must match the standard defined in the
device.
Select the Bellcore caller ID sub standard using the parameter
BellcoreCallerIDTypeOneSubStandard
Select the ETSI FSK caller ID sub standard using the parameter
ETSICallerIDTypeOneSubStandard
- User's Manual 1
- Table of Contents 3
- List of Figures 8
- List of Tables 11
- WEEE EU Directive 13
- Customer Support 13
- Trademarks 13
- Related Documentation 14
- 1 Overview 15
- 1.2 MediaPack Features 16
- 1.3 SIP Overview 17
- Reader’s Notes 18
- 2 Configuration Concepts 19
- 3 Web-Based Management 21
- 3.3.1 Toolbar 24
- 3.3.2 Navigation Tree 25
- 3.3.3.1 Accessing Pages 28
- 3.3.3.2 Viewing Parameters 28
- 3.3.3.5 Working with Tables 32
- 3.3.5.1 Creating a Scenario 36
- 3.3.5.3 Editing a Scenario 39
- 3.3.5.6 Deleting a Scenario 42
- 3.3.7 Getting Help 47
- 3.3.8 Using the Home Page 48
- (grey): channel inactive 49
- 3.4 Configuration Tab 52
- [0] = OAMP (default) 65
- [1] = Media 65
- [2] = Control 65
- 3.4.2 Media Settings 67
- [2] Bypass 70
- [3] Events Only 70
- 3.4.3 Security Settings 79
- [1] Enable = Enabled 116
- [0] Disable (default) 116
- [1] Enable 116
- 5 steps: 120
- To the default Proxy 121
- 3.4.4.1.4 Coders 123
- 4 steps: 130
- 3.4.4.2.3 Metering Tones 144
- 3.4.4.2.5 Keypad Features 147
- 3.4.4.6.1 Authentication 175
- 3.4.4.6.2 Automatic Dialing 176
- 3.4.4.6.4 Call Forward 178
- 3.4.4.6.6 Call Waiting 180
- Disable (default) 188
- No = Don't register 189
- Yes = Register 189
- 3.4.5 Advanced Applications 190
- [1] Enable (Bellcore) 194
- [2] Ericsson MD-110 194
- [3] NEC (ICS) 194
- 3.5 Management Tab 198
- 3.5.1.3 Maintenance Actions 207
- 2 steps: 209
- 3.5.2 Software Update 210
- 3.6.2 Gateway Statistics 223
- 3.6.2.1 Call Counters 224
- 3.6.2.2 Call Routing Status 226
- 3.6.2.3 Registration Status 227
- 3.6.2.5 IP Connectivity 228
- 4 ini File Configuration 231
- 4.2 The ini File Structure 232
- 4.3 Modifying an ini File 235
- 4.4.1 Networking Parameters 236
- 4.4.2 System Parameters 244
- [0] = Disabled (default) 251
- 4.4.4 Security Parameters 252
- 4.4.5 RADIUS Parameters 257
- 4.4.6 SNMP Parameters 258
- [1] = Enabled 268
- Port = Port number 268
- UserId = User name 272
- UserPassword = Password 272
- 4.4.8 Voice Mail Parameters 277
- 4.4.9 PSTN Parameters 279
- [66] = TBR21 280
- Npi = Number Plan 297
- Ton = Type of Number 297
- 4.4.12 Channel Parameters 298
- [0] = Disable (default) 299
- [1] = Enable 299
- [1] Enable (default) 304
- 5 Default Settings 305
- 6.4 Coefficient File 312
- 6.5 User Information File 313
- 7 IP Telephony Capabilities 315
- 7.1.1 Configuring SAS 316
- 7.3.2.1 T.38 Fax Relay Mode 319
- 7.3.3 Supporting V.34 Faxes 324
- 7.4 FXO Operating Modes 326
- 7.4.1.1 One-Stage Dialing 327
- 7.4.1.2 Two-Stage Dialing 328
- 7.4.1.4 DID Wink 329
- 7.4.2 Telephone-to-IP Calls 330
- Connectivity and QoS) 335
- 7.11 Call Detail Record 339
- 7.13 Configuration Examples 342
- 7.14.3 Call Transfer 359
- 7.14.4 Call Forward 360
- 7.14.5 Call Waiting 361
- 7.14.7 Caller ID 362
- 8 Networking Capabilities 365
- 8.2.1 STUN 366
- 8.2.3 No-Op Packets 367
- 8.3 IP Multicasting 368
- 8.8 VLANS and Multiple IPs 370
- Control: Premium control 372
- Management: Bronze 372
- 10.1 MP-11x Specifications 381
- 10.2 MP-124 Specifications 384
- 11 Glossary 387
Manuais e produtos relacionados com Gateways/controladores AudioCodes MediaPack 114
(44 páginas)
(44 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.125 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais